Panasonic WV-SC384 Operating Instructions Manual Download Page 29

Page: 29 / 142

[Network] button

Displays the "Network" page. The network settings

and the settings relating to DDNS (Dynamic DNS),
SNMP (Simple Network Management Protocol) and
the FTP (File Transfer Protocol) periodic transmis-
sion can be configured on the "Network" page.
(

☞

Page 93)

[Schedule] button

Displays the "Schedule" page. On the "Schedule"

page, it is possible to designate time zones to allow
to receive alarm input or to allow to activate the
VMD detection function. (

☞

Page 120)

[Maintenance] button

Displays the "Maintenance" page. System log

check, firmware upgrade, status check and initial-
ization of the setup menu can be carried out on the
"Maintenance" page. (

☞

Page 121)

[Help] button

Displays the "Help" page. (

☞

Page 126)

Camera title

The title of the camera whose settings are currently

being configured will be displayed.

Setup page

Pages of each setup menu will be displayed. There

are tabs for some setup menus. When the under-
lined item is clicked, the corresponding help page
will be displayed.

Summary of Contents for WV-SC384















































































































































Search results

Summary of Contents for WV-SC384

Reviews:

Related manuals for WV-SC384

Brands by name

Popular brands

Panasonic WV-SC384, Operating Instructions Manual

Search results

Summary of Contents for WV-SC384

Reviews:

Related manuals for WV-SC384

Brands by name

Popular brands