manualshive.com logo in svg

Panasonic Switch-M8ePWR PN27089KA, Operation Manual, Page: 92 / 194

Share
Download
Panasonic Switch-M8ePWR PN27089KA Operation Manual Download Page 92

 

 

92 

4.7.1.c. VLAN Creation Menu 

On the VLAN Management Menu, pressing "C" command opens the VLAN 
Creation Menu screen, as shown in Fig. 4-7-3. In this screen, you can configure 
creating new VLAN-related settings. 

 

Fig. 4-7-3 VLAN Creation Menu 

Screen Description 

VLAN ID: 

Indicates the VLAN ID to create. 

VLAN Name: 

Indicates the VLAN name to create. 

Port 
Members: 

Indicates the port numbers belonging to new VLAN members. 

 

 

PN27089K/PN27089KA Local Management System 
VLAN Management -> VLAN Creation Menu 

 
 VLAN ID        : 
 VLAN Name      : 
 
 Port Members   : 
 
 -------------------------------- <COMMAND> ----------------------------------- 
 Set [V]LAN ID 
 Set VLAN [N]ame 
 Select [P]ort Member 
 [A]pply 
 [Q]uit to previous menu 
 
 
 
 
 
 
 
 

Command> 

 Enter the character in square brackets to select option 

 

Summary of Contents for Switch-M8ePWR PN27089KA



































































































































































































Reviews:

No comments