manualshive.com logo in svg

Panasonic Switch-M8ePWR PN27089KA, Operation Manual, Page: 70 / 194

Share
Download
Panasonic Switch-M8ePWR PN27089KA Operation Manual Download Page 70

 

 

70 

4.6.7.e. LED Base Mode Configuration

 

On the System Security Configuration Menu, pressing "B" opens the LED Base 
Mode Configuration screen, as shown in Fig. 4-6-16. On this screen, you can set 
the LED base mode settings. 

 

 

Fig. 4-6-16 LED Base Mode Configuration 

 
Screen Description 

LED Base Mode:

 

Displays the current LED base mode. 
For all ports, the factory default setting is set to the Status mode (Status). 
Status 

Operating in the Status mode. 

Eco 

Operating in the ECO mode. 

 

 

PN27089K/PN27089KA Local Management System 

 System Security Configuration -> LED Base Mode Configuration 
 
 LED Base Mode:             Status 
 
 
 
 
 
 
 
 
 
 
 
 
 Note: Save Configuration to Flash will be executed when LED Base Mode changed. 
 
 -------------------------------- <COMMAND> ----------------------------------- 
 Set LED [B]ase Mode 
 [Q]uit to previous menu 
 
 Command> 
 Enter the character in square brackets to select option 

 

Summary of Contents for Switch-M8ePWR PN27089KA



































































































































































































Reviews:

No comments