manualshive.com logo in svg

Panasonic Switch-M8ePWR PN27089KA, Operation Manual, Page: 45 / 194

Share
Download
Panasonic Switch-M8ePWR PN27089KA Operation Manual Download Page 45

 

 

45 

Available commands are listed below. 

S  Set the SNMP manager status. 

  Press "S." The command prompt changes to "Enter manager entry number>." Enter an 

SNMP manager entry number to change the setting. Then, the command prompt 
changes to "Enable or Disable SNMP manger (E/D)>." Press "E" to enable the SNMP 
manager. Press "D" to disable it. 

I 

Set an IP address for an SNMP manager. 
  Press "I." The command prompt changes to "Enter manager entry number>." Enter an 

SNMP Management entry number to change the setting. Then, the command prompt 
changes to "Enter IP address for manager>." Enter an IP address. 

R  Set access privileges for an SNMP manager. 

  Press "R." The command prompt changes to "Enter manager entry number>." Enter an 

SNMP manager entry number to change the setting. Then, the command prompt 
changes to "Enter the selection>." Press "1" for read-only permission. Press "2" for 
read-and-write. 

C  Set a community name for an SNMP manager. 

  Press "C." The command prompt changes to "Enter manager entry number>." Enter an 

SNMP manager entry number to change the setting. Then, the command prompt 
changes to "Enter community name for manager>." Enter a community name. 

Q  Return to the previous menu. 

 

Summary of Contents for Switch-M8ePWR PN27089KA



































































































































































































Reviews:

No comments