manualshive.com logo in svg

Panasonic Switch-M8ePWR PN27089KA, Operation Manual, Page: 160 / 194

Share
Download
Panasonic Switch-M8ePWR PN27089KA Operation Manual Download Page 160

 

 

160 

Available commands are listed below. 

N  Show the values of the next port. 

 

Press "N." The screen displays the counter values of the next port. The command is 
invalid for Port 10. 

P  Show the values of the previous port. 

 

Press "P." The screen displays the counter values of the previous port. The 
command is invalid for Port 1. 

S  Switch a port to be displayed. 

 

Press "S." The command prompt changes to "Select Port number>." Enter the port 
number you to display the statistics. 

F  Set the display refresh mode. 

 

Press "F." The command prompt changes to "1 for start to refresh,2 for set refresh 
rate." Press "1" to cancel the automatic refresh. Press "2" to change the refresh 
interval.   
If you press "2", the command prompt changes to "Input refresh time>." Enter an 
integer between 5 and 600 (seconds). 

R  Reset counter values. 

 

Press "R." The counter values are reset and immediately changed with those 
accumulated after resetting the counters. 

Q  Return to the previous menu. 

 

Summary of Contents for Switch-M8ePWR PN27089KA



































































































































































































Reviews:

No comments