manualshive.com logo in svg

Panasonic Switch-M8ePWR PN27089KA, Operation Manual, Page: 170 / 194

Share
Download
Panasonic Switch-M8ePWR PN27089KA Operation Manual Download Page 170

 

 

170 

4.9.3. System Reboot

 

 

On the Switch Tools Configuration Menu, pressing "R" opens the System Reboot 
Menu as shown in Fig. 4-9-5. On this screen, you can reboot this Switching Hub. 

 

Fig. 4-9-5 System Reboot 

Screen Description 

Reboot Status: 

Displays whether or not the reboot command is executed. 
Stop 

Displays that the reboot command is not executed. 

Reboot Type: 

Displays the reboot type. The factory default setting is "Normal." 
Normal 

Normal reboot is executed. 

Factory Default 

All settings are reset to factory default. 

Factory Default 
Except IP 

All settings except the IP address are reset to 
factory default. 

Reboot Timer: 

Displays the time between execution of the reboot command and 
actual reboot. The factory default setting is 0 seconds. 

Time Left: 

Displays the time left before the system actually reboots after execution 
of the reboot command. A key entry refreshes the screen display, 
allowing you to check the elapsed time. 

 

PN27089K/PN27089KA Local Management System 

 Switch Tools Configuration -> System Reboot Menu 
 
 Reboot Status:        Stop 
 Reboot Type:          Normal 
 Reboot Timer:         0 seconds 
 Time Left:            N/A 
 
 -------------------------------- <COMMAND> ----------------------------------- 
 
 Set Reboot [O]ption 
 Start [R]eboot Process 
 Set Reboot [T]imer 
 [Q]uit to previous menu 
 
 
 
 
 
 
 
 
 Command> 
 Enter the character in square brackets to select option 

 

 

Summary of Contents for Switch-M8ePWR PN27089KA



































































































































































































Reviews:

No comments