manualshive.com logo in svg

Panasonic Switch-M8ePWR PN27089KA, Operation Manual, Page: 47 / 194

Share
Download
Panasonic Switch-M8ePWR PN27089KA Operation Manual Download Page 47

 

 

47 

Available commands are listed below. 

S  Enable/disable the trap receiver. 

 

Press "S." The command prompt changes to "Enter manager entry number>." Enter an 
entry number for the trap receiver to change the setting. Then, the command prompt 
changes to "Enable or Disable Trap Receiver (E/D)>." Press "E" to enable the TRAP 
receiver. Press "D" to disable it. 

I 

Set an IP address for the trap receiver. 
 

Press "I." The command prompt changes to "Enter manager entry number>." Enter an 
entry number for the trap receiver to change the setting. Then, the command prompt 
changes to "Enter IP address for trap receiver>." Enter the IP address. 

D  Set trap conditions. 

 

Press "D." The screen changes to the Enable/Disable Individual Trap Menu. 
For detailed configuration, refer to the next section (4.6.3.c). 

C  Set a community name for a trap receiver. 

 

Press "C." The command prompt changes to "Enter manager entry number>." Enter an 
entry number for a trap receiver to change the setting. Then, the command prompt 
changes to "Enter community name for trap receiver>." Enter a community name. 

Q  Return to the previous menu. 

 

Summary of Contents for Switch-M8ePWR PN27089KA



































































































































































































Reviews:

No comments