manualshive.com logo in svg

Panasonic Switch-M8ePWR PN27089KA, Operation Manual, Page: 49 / 194

Share
Download
Panasonic Switch-M8ePWR PN27089KA Operation Manual Download Page 49

 

 

49 

Screen Description 

SNMP 
Authentication 
Failure: 

Displays the trap sending settings for an SNMP authentication failure. 
Enabled 

Enables the trap sending. 

Disabled 

Disables the trap sending. (Factory default setting) 

Enabled Link 
Up/Down Port: 

Displays the port number to which a trap is sent, when its link status 
changes. All ports are assigned in factory default setting. 

PoE Trap 
Control: 

Displays the PoE trap control settings. 
Enabled 

Enables the trap sending. (Factory default setting) 

Disabled 

Disables the trap sending. 

Temperature 
Trap Control: 

Displays the trap sending settings when the internal temperature is above or 
below the preset temperature. 
Enabled 

Enables the trap sending. 

Disabled 

Disables the trap sending. (Factory default setting) 

Temperature 
Threshold: 

Displays the threshold temperature value to send the trap. 

 

The factory default setting is 66 degrees C. 

FAN Failure: 

Displays the trap sending settings for an internal fan failure. 
Enabled 

Enables the trap sending. (Factory default setting)

 

Disabled 

Disables the trap sending.

 

 

Summary of Contents for Switch-M8ePWR PN27089KA



































































































































































































Reviews:

No comments