manualshive.com logo in svg

Panasonic Switch-M8ePWR PN27089KA, Operation Manual, Page: 126 / 194

Share
Download
Panasonic Switch-M8ePWR PN27089KA Operation Manual Download Page 126

 

 

126 

Screen Description 

DLF 

Enables/disables the unknown unicast storm control. 

Enabled 

The unknown unicast storm control is enabled. 

Disabled 

The unknown unicast storm control is disabled. 

 

(Factory default setting) 

Broadcast 

Enables/disables the broadcast storm control. 

Enabled 

The broadcast storm control is enabled. 

Disabled 

The broadcast storm control is disabled. (Factory default setting) 

Multicast 

Enables/disables the multicast storm control. 

Enabled 

The multicast storm control is enabled. 

Disabled 

The multicast storm control is disabled. (Factory default setting) 

Threshold 

Displays the threshold of traffic rate (Mbps). 

 
Available commands are listed below. 

D  Enable/disable the unknown unicast storm control. 

 

Press "D." The command prompt changes to "Enter port number>." Enter a port number 
to change the setting. Then, the command prompt changes to "Enable or Disable DLF 
storm control status (E/D)>." Press "E" to enable the unknown unicast storm control, 
and press "D" to disable it. 

B  Enable/disable the broadcast storm control. 

 

Press "B." The command prompt changes to "Enter port number>." Enter a port number 
to change the setting. Then, the command prompt changes to "Enable or Disable 
broadcast storm control status (E/D)>." Press "E" to enable the broadcast storm control, 
and press "D" to disable it. 

M 
 

Enable/disable the multicast storm control. 
 

Press "M." The command prompt changes to "Enter port number>." Enter a port 
number to change the setting. Then, the command prompt changes to "Enable or 
Disable multicast storm control status (E/D)>." Press "E" to enable the multicast storm 
control, and press "D" to disable it. 

T 
 

Set the threshold of traffic rate (Mbps). 
 

Press "T." The command prompt changes to "Enter port number>." Enter a port number 
to change the setting. Then, the command prompt changes to "Enter threshold value." 
Enter the threshold of traffic rate between 1 and 100 (Mbps) for Ports 1 to 8 and 
between 1 and 1000 (Mbps) for Ports 9 to 10. 

Q  Return to the previous menu. 

 

 

Summary of Contents for Switch-M8ePWR PN27089KA



































































































































































































Reviews:

No comments