manualshive.com logo in svg

Panasonic Switch-M8ePWR PN27089KA, Operation Manual, Page: 48 / 194

Share
Download
Panasonic Switch-M8ePWR PN27089KA Operation Manual Download Page 48

 

 

48 

4.6.3.c. Enable/Disable Individual Trap Menu

 

On the SNMP Trap Receiver Configuration Menu screen, pressing "d" opens the 
Enable/Disable Individual Trap Menu screen, as shown in Fig. 4-6-7. On this 
screen, you can set the trap sending settings. 

 

 

Fig. 4-6-7 Enable/Disable Individual Trap 

 

 PN27089K/PN27089KA Local Management System 
 SNMP Trap Receiver Configuration -> Enable/Disable Individual Trap Menu 
 
 SNMP Authentication Failure :    Disabled 
 Enable Link Up/Down Port:        1-10 
 PoE Trap Control:                Enabled 
 Temperature Trap Control:        Disabled 
 Temperature Threshold:           66 degree(s) Celsius 

FAN Failure:                     Enabled 

 
 -------------------------------- <COMMAND> ----------------------------------- 
 
 Enable/Disable [A]uth Fail Trap 
 Add Link Up/Down Trap [P]orts 
 [D]elete Link Up/Down Trap Ports 
 Enable/Disable Po[E] Trap 
 Enable/Disable [T]emperature Trap 
 [S]et Temperature Threshold 

Enable/Disable [F]AN Fail Trap 

 [Q]uit to previous menu 
 
 
 
 Command> 
 Enter the character in square brackets to select option 

 

Summary of Contents for Switch-M8ePWR PN27089KA



































































































































































































Reviews:

No comments