manualshive.com logo in svg

Panasonic Switch-M8ePWR PN27089KA, Operation Manual, Page: 116 / 194

Share
Download
Panasonic Switch-M8ePWR PN27089KA Operation Manual Download Page 116

 

 

116 

Available commands are listed below. 

E  Set Edge Status of each port. 

 

Press "E" to change the command prompt to "Select port number to be changed>." 
Enter a port number. Then, "Set edge port for port # (T/F)>" is displayed. For True, 
press "T." For False, press "F." 

T  Set P-to-P Status of each port. 

 

Press "T" to change the command prompt to "Select port number to be changed>." 
Enter a port number. Then, "Set point-to-point port for port # (A/T/F)>" is displayed. For 
Auto, press "A." For True, press "T." For False, press "F." 

M  Restart the operation of the spanning tree. 

 

Press "M" to change the command prompt to "Select port number to be changed>." 
Enter a port number. Then, "Restart the protocol migration process for port #? (Y/N)>" 
is displayed. If you restart, press "Y." If not, press "N." 

Q  Return to the previous menu. 

 

Summary of Contents for Switch-M8ePWR PN27089KA



































































































































































































Reviews:

No comments