manualshive.com logo in svg

Panasonic Switch-M8ePWR PN27089KA, Operation Manual, Page: 89 / 194

Share
Download
Panasonic Switch-M8ePWR PN27089KA Operation Manual Download Page 89

 

 

89 

Screen Description 

Internet 
Mansion: 

Displays a status of Internet Mansion mode. 
Enabled 

Internet Mansion mode is enabled. 

Disabled 

Internet Mansion mode is disabled. (Factory default setting) 

Uplink: 

Indicates an Uplink port when Internet Mansion mode is enabled. 

VLAN ID 

Indicates a VLAN ID of VLAN. 

VLAN 
Name 

Indicates a VLAN name that has been configured. 

VLAN Type  Indicates a type of VLAN. 

Permanent 

Indicates that the VLAN is the one of initial setting. At least one 
VLAN must exist and this VLAN cannot be deleted. 

Static 

Indicates that the VLAN is the newly configured one. 

Mgmt 

Indicates whether the VLAN is a management VLAN or not. 
UP 

Indicates that the VLAN is a management VLAN (VLAN that is 
possible to communicate with CPU). 

DOWN 

Indicates that the VLAN is not a management VLAN. 

 

Note:

 

All ports belong to VLAN ID=1 (default VLAN) in factory default setting, 
and the management VLAN status of VLAN ID=1 is UP. 

Summary of Contents for Switch-M8ePWR PN27089KA



































































































































































































Reviews:

No comments