manualshive.com logo in svg

Panasonic Switch-M8ePWR PN27089KA, Operation Manual, Page: 143 / 194

Share
Download
Panasonic Switch-M8ePWR PN27089KA Operation Manual Download Page 143

 

 

143 

4.7.10. Ring Redundant Protocol Configuration

 

 

On the Advanced Switch Configuration Menu screen, pressing "R" opens the 
Ring Redundant Protocol Configuration screen as shown in Fig. 4-7-31. On this 
screen, you can configure the Ring Redundant Protocol (RRP). 
 

 

Fig. 4-7-31 Ring Redundant Protocol Configuration Menu 

 PN27089K/PN27089KA Local Management System 
 Advanced Switch Configuration -> Ring Redundant Protocol Configuration 
 
 RRP Status : Disabled         Total Domain Number : 0 
 Domain Name                Ctrl VLAN  Data VLAN(s) Ring Status Node Type 
 ------------------------- ----------- ------------ ----------- --------- 
 
 
 
 
 
 
 
 
 
 
 
 -------------------------------- <COMMAND> ----------------------------------- 
 Set RRP [S]tatus                        [M]odify RRP Domain 
 [C]reate RRP Domain                     [D]elete RRP Domain 
 S[h]ow RRP Domain information           [Q]uit to previous menu 
 
 Command> 
 Enter the character in square brackets to select option 

 

Summary of Contents for Switch-M8ePWR PN27089KA



































































































































































































Reviews:

No comments