manualshive.com logo in svg

Panasonic Switch-M8ePWR PN27089KA, Operation Manual, Page: 139 / 194

Share
Download
Panasonic Switch-M8ePWR PN27089KA Operation Manual Download Page 139

 

 

139 

4.7.9.a. PoE Port Configuration Menu

 

On the Power Over Ethernet Configuration Menu, pressing "P" opens the PoE 
Port Configuration Menu as shown in Fig. 4-7-29. On this screen, you can 
configure PoE settings for each port. 

 

 

Fig. 

 

4-7-29 PoE Port Configuration Menu

 

 

PN27089K/PN27089KA Local Management System 

 Power Over Ethernet Configuration -> PoE Port Configuration Menu 
 
 No. Admin  Status        Class Limit(mW)   Pow.(mW)   Vol.(V)   Cur.(mA) 
 --- ----- -------------- ----- ---------  ---------  --------- ---------- 
  1   Up   Not Powered       0      15400          0          0          0 
  2   Up   Not Powered       0      15400          0          0          0 
  3   Up   Not Powered       0      15400          0          0          0 
  4   Up   Not Powered       0      15400          0          0          0 
  5   Up   Not Powered       0      15400          0          0          0 
  6   Up   Not Powered       0      15400          0          0          0 
  7   Up   Not Powered       0      15400          0          0          0 
  8   Up   Not Powered       0      15400          0          0          0 
 
 
 
 
 
 -------------------------------- <COMMAND> ----------------------------------- 
 Set PoE Port Admin [S]tatus           Set PoE Port Power [L]imit 
 [Q]uit to previous menu 
 
 Command> 
 Enter the character in square brackets to select option 

 

Summary of Contents for Switch-M8ePWR PN27089KA



































































































































































































Reviews:

No comments