manualshive.com logo in svg

Panasonic MINAS-A5NL Series, Technical Reference

Share
Download
Panasonic MINAS-A5NL Series Technical Reference Download Page 116

No. SX-DSV02310 - 108 - 

R2.0 Motor 

Business 

Division, 

Appliances Company, Panasonic Corporation 

 

7-1-5 Variations in command position during command updating period 

 

7-1-5-1 Limiting variations in command position 

 

When applying the movement command, make sure that variations in command position during command updating 
period will not exceed the maximum overspeed level. 
 
Allowable input movement command value of servo driver (variations of command position during 1 s multiplied by 
the electronic gear ratio) is 400 M pulses/s.   
 
The movement command should not cause variations that may exceed the smaller one of these limits.   
If a variation of command position during communication period is too large, Err. 27.4 (Command error protection) will 
be activated. 

 

7-1-5-2 Wrap rounding command position 

 

If a variation of command position during communication period has exceeded 7FFFFFFFh, wraparound process starts. 

 

 

 

7-1-5-3 Clearing position deviations   

 

When clearing position deviations from the host controller, read the actual position (APOS) and set command position 
to the value so that actual position (APOS) becomes equal to command position (CPOS). 
 
Note that, as in the case of 7-1-4-1, change the command position (CPOS) gradually by dividing the command updating 
period in several sub-periods so that variations in command position will not exceed the limit. 

 

7FFFFFFFh 

80000000h 

In positive direction 1 
(command unit) relative 
displacement (wraparound 
process) 

In negative direction 
4294967295 (command 
unit) no relative 
displacement 

Physical 
position 

80000000h 

Servo internal computation 
Command position (command unit) 

Example of wraparound process: Command position changed from 7FFFFFFFh to 80000000h 

Summary of Contents for MINAS-A5NL Series
















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands