– 104 –
Chapter 4 Shooting — Viewfinder status display
6 External GPS display
This is displayed when the main menu
→
[SYSTEM]
→
[SYSTEM SETUP]
→
[GPS] is set to [EXTERNAL].
f
The strength of signal reception is not displayed.
7 4G/LTE connection status and the bonding device status display
Displays the 4G/LTE connection status.
Displays the following when connected to 4G/LTE. The signal reception strength is displayed in 6 levels. The number of vertical bars represent the
signal strength. Not displayed when the 4G/LTE setting is disabled.
[4G/LTE ]
Displayed when connected to 4G/LTE.
[4G/LTE
]
Displayed when not connected to 4G/LTE.
[4G/LTE
]
Displayed when there is an error in the 4G/LTE connection.
Displays the bonding device status. Displays the device status received from the bonding device. The strength of the signal reception is displayed in
6 levels, and remaining battery is displayed in 6 levels. [E] is displayed when there is an error in the bonding device.
@
@
NOTE
t
Depending on the 4G/LTE USB modem that is supported, vertical bars that indicate the signal strength may not be displayed.
t
The device status may not be acquired depending on the connected bonding device.
t
For details on bonding device that the camera can acquire the device status, visit the support desk at the following website:
https://pro-av.panasonic.net/
8
Camera warning, notification display area
(Related to automatic white balance, automatic black balance and switch operation)
[AWB A ACTIVE]
Displayed when automatic white balance is active on the <A> channel.
[AWB B ACTIVE]
Displayed when automatic white balance is active on the <B> channel.
[AWB A OK
*
.
*
K]
Displayed when automatic white balance has ended successfully on the <A> channel.
[AWB B OK
*
.
*
K]
Displayed when automatic white balance has ended successfully on the <B> channel.
[AWB BREAK
*
.
*
K]
Displayed when automatic white balance operation is forcibly ended.
[AWB NG]
Displayed when automatic white balance operation is not ended successfully. The 2nd line displays that status.
[COLOR TEMP LOW]
Warns that the color temperature is too low.
[COLOR TEMP HIGH]
Warns that the color temperature is too high.
[LEVEL OVER]
Warns that the brightness is too high.
[LOW LIGHT]
Warns that the brightness is too low.
[TIME OVER]
Warns that processing could not be executed within the operation time.
[ATW MODE]
Displayed when automatic white balance cannot be executed due to activation of auto tracking white balance.
[AWB PRESET
*
.
*
K]
Displayed when the <WHITE BAL> switch is set to <PRST> and automatic white balance operation cannot be executed.
[AWB UNABLE]
Displayed when automatic white balance operation cannot be executed. The 2nd line displays that status.
[S.GAIN MODE]
Displayed when super gain is active.
[CHECK FILTER]
Prompts re-confirmation of the filter switching dial position when the power is turned on and automatic white balance is active.
[ABB ACTIVE]
Displayed when automatic black balance operation is active.
[ABB OK]
Displayed when automatic black balance operation is ended successfully.
[ABB BREAK]
Displayed when automatic black balance operation is forcibly ended.
[ABB NG]
Displayed when automatic black balance operation is not ended successfully.
[B-SHD READY]
Displayed when black shading operation is accepted by holding down the <AUTO W/B BAL> switch during automatic black
balance operation.
[B-SHD ACTIVE]
Displayed when black shading operation is active.
[B-SHD OK]
Displayed when black shading operation is ended.
[B-SHD BREAK]
Displayed when black shading operation is forcibly ended.
[B-SHD NG]
Displayed when black shading operation is not ended successfully.
(Switch selection display)
[WHITE:#]
Displayed when the <WHITE BAL> switch is switched. One of [A]/[B]/[PRST] is displayed at [#].
[ATW MODE]
Displayed when automatic tracking white balance operation is set.
[
*
.
*
K]
Displays the currently set color temperature.
[AUTO KNEE:ON/OFF]
Displayed when the <OUTPUT>/<AUTO KNEE> selector switch where [ON] or [OFF] is assigned in the main menu
→
[CAMERA]
→
[SW MODE]
→
[AUTO KNEE SW] is set to <ON>/<OFF>.
[DRS:ON/OFF]
Displayed when the <OUTPUT>/<AUTO KNEE> selector switch where [DRS] is assigned in the main menu
→
[CAMERA]
→
[SW MODE]
→
[AUTO KNEE SW] is set to <ON>/<OFF>.
[GAIN:
**
dB
+
**
↑
]
Displayed when gain is switched by the <GAIN> switch or <USER> button. When digital super gain is active, that value is
displayed at the same time.
[SS:1/
****
] or
[
***
.
*
deg]
When the shutter speed is switched, that value is displayed.
[SS:
w
1/
****
] or
[
w***
.
*
d]
Displayed when syncro scan is selected for the shutter speed.
[CC:
****
**
K]
Displayed when the <CC FILTER> dial position is switched.
[ND:
*
]
Displayed when the <ND FILTER> dial position is switched.
[EXTENDER:ON/OFF]
Displays the status of the lens extender.
