Zone
Zone
VCB-X STATUS
VCB-X Operator Interface SD
56
Screen #16
Preheat-X Enabled and Leaving Air Temperature
Setpoint
Screen #17
Current Preheat-X Leaving Air Temperature and
Entering
Air
Temperature
Screen #18
Current Preheat-X Modulating Position and
Active
Stages
Screen #19
Current Outdoor Air Drybulb and Current
Outdoor
Air
Relative
Humidity
Screen #20
Current Wetbulb Temperature and Current
Calculated
Outdoor
Air
Dewpoint
Temperature
Screen #21
Economizer Enabled or Disabled and Current
Economizer
Open
Percentage
Screen #22
Economizer Feedback Percentage for Title 24
Economizer
Screen #23
Economizer in IAQ Mode Yes/No and
Economizer
Minimum
Percentage
Screen #24
Current CO
2
Level, Minimum Setpoint, and
Maximum
Setpoint
Screen #25
Outdoor Air CFM and Supply Air CFM
Screen #26
Return Air CFM and Exhaust Air CFM
Screen #27
Current Duct Static Pressure, Current Duct Static
Pressure Setpoint and Output Percentage
Screen #28
Current Building Pressure and Setpoint
Screen #29
Building Pressure Exhaust Fan Status and Output
Signal
Percentage
Screen #30
Current Head Pressure 1 Reading, Head Pressure
Setpoint, and Condenser 1 Signal
Screen #31
Current Head Pressure 2 Reading, and Condenser
2
Signal
Screen #32
Leaving Water Temperature, Entering Water
Temperature & Current Suction Pressure
Screen #33
WSHP Glycol Percentage and Heating & Cooling
Modes
Low
Suction
Setpoints
Screen #34
WSHP Glycol Percentage, Unsafe Suction
Setpoint,
and
Low
Leaving
Water
Temperature
Screen #35 Return Air Damper Signal & Return Air Bypass
Damper
Signal
Screen #36
Reset Voltage Signal
Screens
#37-42 VCB-X
Relays
Screens
#43-47
VCB-X EM1 Relays
Screens
#48-59
12 Relay Expansion Module Relays
Screens
#60-90
Alarm Status Screens
Status Screens - General Procedures
From any menu screen,
press
<STATUS>
. The
Unit Selection Screen,
shown below, will appear requesting that you enter the unit ID number.
Enter Unit Address
Then Press Enter
Selected Unit#: XXXX
No Communication
Enter
the correct unit ID number of the Controller you want to view and
press
<ENTER>
. Once communication is established, “No Communica-
tion” will be replaced with “Press Down.” Then
press
<
>
. You will
then see Setpoint Screen #1.
Press
<ENTER>
to save entered data and
press
<
>
to scroll through the screens.
NOTE:
If “No Communication” remains, it indicates a
communication failure to the controller.
Status Screen Index
The available Status Screens for the VCB-X Controller are listed on the
next few pages by sequential screen number. The following is a list of
all the VCB-X Status Screens in numerical order with a brief listing of
the Status features available on each screen:
Screen #1
Date & Time
Screen #2
Application Type, Schedule Mode & HVAC
Mode
Screen #3
Controlling Temperature, Cooling & Heating
Setpoints
Screen #4
Space & Return Air Temperature & Slide Adjust
Screen #5
Supply Air Temperature & Active Setpoint
Screen #6
Cooling Enabled Yes/No
Screen #7
Cooling Outputs - Active Stages & Mod Cooling
Position
Screen #8
Compressor Discharge Temperature
Screen #9
Heating Enabled Yes/No or HP Heat Enabled, HP
Aux Enabled & HP Emergency Heat Enabled
Screen #10
Heating Outputs - Active Stages & Mod Heat
Position
Screen #11
MODGAS-X Enabled or Disabled and /
MODGAS-X
Heating
Output
Signal
Screen #12
Current Indoor RH & Indoor RH Setpoint
Screen #13
Current Coil Temperature, Current Coil Setpoint,
and
Suction
Pressure
Screen #14
Active Reheat Stages
Screen #15
MHGRV-X Enabled or Disabled and MHGRV-X
Reheat
Valve
Output
Signal
Percentage
VCB-X Status Screens
