Oki MB760 Service Manual Download Page 96

Page: 96 / 390

45641001TH Rev.1

5-13 /

Oki Data CONFIDENTIAL

6. File sharing related error

Error code

Message displayed in the

Web Page screen

Contents

Troubleshooting

2D10

Illegal Job status

System access abnormality

P. 5-73

2D11

Not enough memory

Insufficient memory

P. 5-73

2D12

Illegal Job status

Message reception error

P. 5-73

2D13

Illegal Job status

Message transmission error

P. 5-73

2D14

Invalid parameter specified

Invalid parameter

P. 5-74

2D15

Document size exceeded
limit or maximum size.

Exceeding the maximum size for file
sharing

P. 5-74

2D30

Failed to create directory

Directory creation failure

P. 5-74

2D31

Failed to create file

File creation failure

P. 5-74

2D32

Failed to delete file

File deletion failure

P. 5-73

2D33

Failed to create file

File access failure

P. 5-74

2D40

Failed to convert image file
format

Image conversion abnormality

P. 5-74

2D43

Encryption error. Failed to
create file

Encryption error

P. 5-74

2D44

Creating the image file was
not permitted.

Encryption PDF enforced mode error

P. 5-74

2D45

Failed in making meta data.

Meta data creation error (Scan to File)

P. 5-74

2D62

Failed to connect to
network destination. Check
destination path

File server connection error

P. 5-74

2D63

Specified network path is
invalid. Check destination
path

Invalid network path

P. 5-74

2D64

Logon to file server failed.

Check username and
password

P. 5-74

2D65

There are too many
documents in the folder.
Failed in creating new
document.

Exceeding documents in folder: Creating
new document is failed.

P. 5-74

2D66

Failed To Process your Job.
Insufficient Storage space.

Storage capacity full failure during
processing

P. 5-74

2D67

FTP service is not available

FTP service not available

P. 5-75

2D68

File Sharing service is not
available

File sharing service not available

P. 5-75

2D69

NetWare service is not

available

NetWare service not available

P. 5-75

2DA0

Expired scan documents
deleted from share folder.

Periodical deletion of scanned
documents completed properly.

2DA1

Expired Sent Fax documents
deleted from shared folder.

Periodical deletion of transmitted FAX

documents completed properly.

2DA2

Expired Received Fax
documents deleted from
shared folder.

Periodical deletion of received FAX

documents completed properly.

2DA3

Scanned documents in
shared folder deleted upon

user’s request.

Manual deletion of scanned documents
completed properly.

Summary of Contents for MB760







































































































































































































































































































































































































Search results

Summary of Contents for MB760

Reviews:

Related manuals for MB760

Brands by name

Popular brands

Oki MB760, Service Manual

Search results

Summary of Contents for MB760

Reviews:

Related manuals for MB760

Brands by name

Popular brands