Oki MB760 Service Manual Download

Page: 123 / 390

45641001TH Rev.1

5-40 /

Oki Data CONFIDENTIAL

5.3.4

Communication related service call

[F070] Communication error between sYs board and PU board

Classification

Error content

Communication related
service call

Communication error between SYS board and PU board

Check item

Measures

Error code

• Turn the power OFF and then back ON using the main power switch,

and then check if the error code changes to another one.

• If it changes to another one, follow the procedure for the changed error

code.

Check firmware version

• Check the version of the system firmware on the SYS board.
• Check the version of the PU firmware on the PU board.

Board check

• Check if the connector CN118, CN119 on the SYS board and the

connector CUIF0, CUIF1 on the PU board are completely inserted.

• Check if the connector pin between the SYS board (connector CN118,

CN119) and the PU board (CUIF0, CUIF1) is disconnected.

• Check if the connectors HEAD0K, HEAD1Y, HEAD2M, and HEAD3C

of the LED head are completely inserted, and the harness is

disconnected or open circuited.

• Check if the conductor patterns on the PU board and SYS board are

short circuited or open circuited

Parts to be replaced

Remark

SYS board

PU board

LED head

[F071] Communication initialization error between sYs board and PU board

Classification

Error content

Communication related
service call

Communication initialization error between SYS board and PU board

Proce-

dure

Check item

Measures

LED head, harness

1-1. Disconnect all the harnesses of the LED heads, and then turn

the power ON. Check if the error changes to another service call.

(HEAD0K, HEAD1Y, HEAD2M, HEAD3C)

1-2. If the error does not change to another service call in step 1-1, go to

step 2. If the error changes to another service call, follow the steps

below.

1-3. Connect the harnesses of the LED head to the PU board single

color at a time, and then turn the power ON to identify the LED head

in error. Check if F071 occurs. Place the parts causing the error.

Y color: HEAD1Y
M color: HEAD2M
C color: HEAD3C

K color: HEAD0K

Check firmware
version

• Check the version of the system firmware on the SYS board.
• Check the version of the PU firmware on the PU board.

Summary of Contents for MB760







































































































































































































































































































































































































Search results

Summary of Contents for MB760

Reviews:

Related manuals for MB760

Brands by name

Popular brands

Oki MB760, Service Manual

Search results

Summary of Contents for MB760

Reviews:

Related manuals for MB760

Brands by name

Popular brands