Oki MB760 Service Manual Download

Page: 167 / 390

45641001TH Rev.1

5-84 /

Oki Data CONFIDENTIAL

[501B] No URL (host/port) or invalid path

Classification

Error item

Communication error with
external application

Initial URL is invalid.

Check item

Measures

Setting

Set the correct initial URL.

[5030] HTTP communication error

Classification

Error item

Communication error with
external application

An error in the HTTP communication

Check item

Measures

Setting

Check the URL for communication.

Check that the valid IP address is assigned to connect to the server.

[50FF] eBR2 internal error

Classification

Error item

MFP internal error

A fatal error occurred in the MFP

Check item

Measures

Setting

Restart the MFP, and then try again.

[5110] Toner cartridge detection error

Classification

Error item

Web Page related error

Check item

Measures

Setting

• Check if the toner cartridge is installed properly.
• Check if the toner cartridge detection sensor operates properly.

[5212] Time for cleaning of the slit glass and main charger

Classification

Error item

Web Page related error

Check item

Measures

Setting

• Clean the LED head and main charger.
• If the message is not cleared after the cleaning, check if there is any

detection error, breakage or poor connection of the needle electrode

cleaner detection sensor.

Summary of Contents for MB760







































































































































































































































































































































































































Search results

Summary of Contents for MB760

Reviews:

Related manuals for MB760

Brands by name

Popular brands

Oki MB760, Service Manual

Search results

Summary of Contents for MB760

Reviews:

Related manuals for MB760

Brands by name

Popular brands