Oki MB760 Service Manual Download | Manualshive

Page: 285 / 390

background image

45641001TH Rev.1

9-4 /

Oki Data CONFIDENTIAL

[C] Confirmation of the error

“Backup Failed” or “Restore Failed” is displayed on the lower left part of the LCD screen

when the data have not been properly backed up or restored.

Moreover, details of an error are displayed under the above message.
(The following is an example screen when “USB device not detected” is displayed.)

SRAM Data Cloning Mode

Firmware Version : x. x. x. x

Select number (1-2) and press START key

Backup Failed
USB device not detected

Update Mode : 59 Mode

2: Restore SRAM Data from USB

Fig.12-1

In this case, turn the power OFF and then check the following items. After confirming and
solving the problem, back up / restore the data again from the beginning.

•  Does the USB device meet the conditions being used for this cloning?
•  Is the updated program file written on the USB device properly?
•  Is the USB device installed properly?
•  Is the USB device or the equipment damaged?

Backup

Display content

Error content

USB device not detected

The USB device has not been installed.

SRAM Device Not Connected

The SRAM board (for the SYS board) has not been installed.

Backup not created

Creation of the Backup file of data of the SRAM board (for
the SYS board) has been failed.

Encryption Failed

An encryption of the backup file has been failed.

password Not Appended to Backup Addition of the encryption password has been failed.

MFP Serial Number Not Set

Acquisition of the MFP Serial No. has been failed.

Restore

Display content

Error content

USB device not detected

The USB device has not been installed.

SRAM Device Not Connected

The SRAM board (for the SYS board) has not been installed.

Invalid Backup File

The SYS board has not been recognized.

No Backup File Exists

Backup file has not existed in the USB device.

Invalid password

An incorrect password has been entered.

Decryption Failed

Decoding of the backup file has been failed.

Invalid MFP Serial Number:
xxxxxxxxx

An incorrect MFP Serial No. has been entered.

MFP Serial Number Not Set

Acquisition of the MFP Serial No. has been failed.

Backup File Corrupted

A backup file has been damaged.

«
...
283
284
285
286
287
...
»

Summary of Contents for MB760







































































































































































































































































































































































































Reviews:

No comments

Related manuals for MB760

Brand: DataCard Pages: 17

Brand: DataCard Pages: 24

SCX-4300 - SCX 4300 B/W Laser

Brand: Samsung Pages: 97

SCX 4828FN - Laser Multi-Function Printer

Brand: Samsung Pages: 151

SCX 4725FN - B/W Laser - All-in-One

Brand: Samsung Pages: 120

SCX 4500 - B/W Laser - All-in-One

Brand: Samsung Pages: 97

SCX 4200 - B/W Laser - All-in-One

Brand: Samsung Pages: 95

SCX 4500 - B/W Laser - All-in-One

Brand: Samsung Pages: 172

ProXpress M337x

Brand: Samsung Pages: 56

PROXPRESS M332 SERIES

Brand: Samsung Pages: 50

ML-2240 - 23 Ppm Mono Laser Printer

Brand: Samsung Pages: 82

Brand: Samsung Pages: 8

ML-1610 - B/W Laser Printer

Brand: Samsung Pages: 134

ML-1610 - B/W Laser Printer

Brand: Samsung Pages: 112

Brand: Samsung Pages: 128

Brand: Samsung Pages: 152

ML 3471ND - B/W Laser Printer

Brand: Samsung Pages: 207

ML 2150 - B/W Laser Printer

Brand: Samsung Pages: 237

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands