Oki MB760 Service Manual Download Page 310

Page: 310 / 390

45641001TH Rev.1

11-12 /

Oki Data CONFIDENTIAL

05/

Mode

Element

Sub

element

Item

Subitem

Code Sub-

code

Details

Default

value

Acceptable

value

RAM

Contents

Proce-

dure

Adjustment

mode

Image
Processing

Gamma
balance

adjustment

SCN(black)

User custom

7480

High density

128

0-255

SYS

The larger the value, the darker the image of the

area surrounding the target area becomes.

Adjustment

mode

Image
Processing

Gamma
balance

adjustment

SCN(black)

Text/Photo

7485

Low

density

128

0-255

SYS

The larger the value, the darker the image of the

area surrounding the target area becomes.

Adjustment

mode

Image
Processing

Gamma
balance

adjustment

SCN(black)

Text/Photo

7485

Medium density

128

0-255

SYS

The larger the value, the darker the image of the

area surrounding the target area becomes.

Adjustment

mode

Image
Processing

Gamma
balance

adjustment

SCN(black)

Text/Photo

7485

High density

128

0-255

SYS

The larger the value, the darker the image of the

area surrounding the target area becomes.

Adjustment

mode

Image
Processing

Gamma
balance

adjustment

SCN(black)

Text

7486

Low

density

128

0-255

SYS

The larger the value, the darker the image of the

area surrounding the target area becomes.

Adjustment

mode

Image
Processing

Gamma
balance

adjustment

SCN(black)

Text

7486

Medium density

128

0-255

SYS

The larger the value, the darker the image of the

area surrounding the target area becomes.

Adjustment

mode

Image
Processing

Gamma
balance

adjustment

SCN(black)

Text

7486

High density

128

0-255

SYS

The larger the value, the darker the image of the

area surrounding the target area becomes.

Adjustment

mode

Image
Processing

Gamma
balance

adjustment

SCN(black)

Photo

7487

Low

density

128

0-255

SYS

The larger the value, the darker the image of the

area surrounding the target area becomes.

Adjustment

mode

Image
Processing

Gamma
balance

adjustment

SCN(black)

Photo

7487

Medium density

128

0-255

SYS

The larger the value, the darker the image of the

area surrounding the target area becomes.

Adjustment

mode

Image
Processing

Gamma
balance

adjustment

SCN(black)

Photo

7487

High density

128

0-255

SYS

The larger the value, the darker the image of the

area surrounding the target area becomes.

Adjustment

mode

Image
Processing

Gamma
balance

adjustment

SCN(black)

Gray scale

7488

Low

density

128

0-255

SYS

The larger the value, the darker the image of the

area surrounding the target area becomes.

Adjustment

mode

Image
Processing

Gamma
balance

adjustment

SCN(black)

Gray scale

7488

Medium density

128

0-255

SYS

The larger the value, the darker the image of the

area surrounding the target area becomes.

Adjustment

mode

Image
Processing

Gamma
balance

adjustment

SCN(black)

Gray scale

7488

High density

128

0-255

SYS

The larger the value, the darker the image of the

area surrounding the target area becomes.

Adjustment

mode

Image
Processing

Image

scanning

7489

Amount of
surrounding void

0-255

SYS

When the value increases, the blank area around

the scanned image becomes wider. (e.g.: In
network

scanning with 600 dpi, if the setting value

is “1”,

the blank area increases by 1 dot.)

Summary of Contents for MB760







































































































































































































































































































































































































Search results

Summary of Contents for MB760

Reviews:

Related manuals for MB760

Brands by name

Popular brands

Oki MB760, Service Manual

Search results

Summary of Contents for MB760

Reviews:

Related manuals for MB760

Brands by name

Popular brands