Oki MB760 Service Manual Download Page 198

Page: 198 / 390

45641001TH Rev.1

6-12 /

Oki Data CONFIDENTIAL

3. ID=05 and c5

Name

Description

Remarkd

Re-allocated Sector
Count

The number of sectors reassigned

This value tends to
increase at HDD
failure.

Current Pending
Sector Count

The number of candidate sectors to be reassigned

This value tends to
increase at HDD
failure.

4. Description of each ID

Name

Meaning

Read Error Rate

This attribute is a measure of the read error rate.

Throughput Performance

This attribute is a measure of the throughput performance.

Spin Up Time

This attribute is a measure of how quickly the drive is able to

spin up from a spun down condition.

Spin Start/Stop Count

This attribute is a measure of the total number of spin ups from
a spun down condition.

Re-allocated Sector Count

This attribute is a measure of the total number of reallocated
sectors.

Seek Error Rate

This is a measure of the seek error rate.

Seek Time Performance

This attribute is a measure of a drive’s seek performance during
normal online operations.

Power-On Hours

This attribute is a measure of the total time (hours or minutes
depending on disk manufacturer) the drive has been on.

Spin Retry Count

This attribute is a measure of the total number of spin retries.

Power Cycle Count

This attribute is a measure of the number of times the drive has
been turned on.

Power off Retract Count

This attribute is a measure of the total number of emergency
unloads.

Load Cycle Count

This attribute is a measure of the total number of load/unloads.

Temperature

This attribute is a measure of the temperature in the HDD.

ECC On the Fly Count

This attribute is a measure of the total number of the ECC On
the Fly.

Reallocation Event Count

This attribute is a measure of the total number of the reallocation
events.

Current Pending Sector Count

This attribute is a measure of the total number of candidate
sectors to be reallocated.

Off-Line Scan Uncorrectable

Sector Count

This attribute is a measure of the total number of uncorrectable
sectors found during the off-line scan.

Ultra DMA CRC Error Count
(Rate)

This attribute is a measure of the total number of errors found in
data transfer in the Ultra-DMA mode.

Write Error Rate

This attribute is a measure of the write error rate.

Notes:

“Over-range” is displayed if the number of digits acquired from the HDD exceeds the maximum
digits which can be displayed on the control panel; however, this does not indicate an error.

Summary of Contents for MB760







































































































































































































































































































































































































Search results

Summary of Contents for MB760

Reviews:

Related manuals for MB760

Brands by name

Popular brands

Oki MB760, Service Manual

Search results

Summary of Contents for MB760

Reviews:

Related manuals for MB760

Brands by name

Popular brands