Oki MB760 Service Manual Download | Manualshive

Page: 157 / 390

background image

45641001TH Rev.1

5-74 /

Oki Data CONFIDENTIAL

[2D14] Invalid parameter

When a template is used, form the template again.
If the error still occurs, turn the power OFF and then back ON, and perform the job again.

[2D15] exceeding the maximum size for file sharing

Divide the file in error into several files and retry. Or retry the job in a single-page format.

[2D30] Directory creation failure
[2D31] File creation failure
[2D33] File access failure

Check if the access privilege to the storage directory is writable.
Check if the server or local disk has a sufficient space in disk capacity.

[2D40] Image conversion abnormality

Turn the power OFF and then back ON. Perform the job in error again.
Replace the main memory and perform the job again.

[2D43] encryption error

Turn the power OFF and then back ON. Perform the job in error again.

[2D44] encryption PDF enforced mode error

Reset the encryption and perform the job in error again.
If an image file not encrypted is created, consult your administrators.

[2D45] meta data creation error (scan to File)

Check the template settings. Perform the job in error again. If the error still occurs, turn the
power OFF and then back ON, and then perform the job in error again.

[2D62] File server connection error

Check the IP address or path of the server.
Check if the server is operating properly.

[2D63] Invalid network path

Check the network path.

If the path is correct, turn the power OFF and then back ON, and perform the job again.

[2D64] Login failure

Reset the login name and password. Perform the job.

Check if the account of the server is properly set up.

[2D65] exceeding documents in folder: Creating new document is failed

Delete some documents in the folder.

[2D66] storage capacity full failure during processing

Delete the job in progress or being set or in the HOLD/PRIVATE/PROOF/INVALID, and

perform it again.
Check if the server or local disk has a sufficient space in disk capacity.
Check that there is enough space in the server or local disk.

«
...
155
156
157
158
159
...
»

Summary of Contents for MB760







































































































































































































































































































































































































Reviews:

No comments

Related manuals for MB760

RS/6000 44P Series 270

Brand: IBM Pages: 216

Brand: imagistics Pages: 57

WorkCentre Pro 90

Brand: Xerox Pages: 36

MP 2554SP Series

Brand: Ricoh Pages: 1

Brand: Radio Shack Pages: 42

DocuPrint C3300 DX

Brand: Xerox Pages: 200

Brand: Oki Pages: 105

Brand: Pantum Pages: 155

Brand: Tektronix Pages: 178

Brand: Oki Pages: 204

Brand: Oce Pages: 366

Brand: Olivetti Pages: 132

Brand: Oce Pages: 76

Brand: Epilog Laser Pages: 92

imageprograf IPF785

Brand: Canon Pages: 640

VIP-5000 Series

Brand: Daktronics Pages: 62

Brand: Panasonic Pages: 12

KX-P1150 - KX-P 1150 B/W Dot-matrix Printer

Brand: Panasonic Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands