Oki MB760 Service Manual Download | Manualshive

Page: 162 / 390

background image

45641001TH Rev.1

5-79 /

Oki Data CONFIDENTIAL

5.3.9

Printer function error

[4011] Print job cancellation

This message appears when deleting the job on the screen.

[4021] Print job power failure

When there are running jobs, perform the job in error again after the completion of the
running jobs.
If the error still occurs, turn the power OFF and then back ON, and perform the job again.

[4031] HDD full error

Delete unnecessary private print jobs and invalid department print jobs.

[4041] User authentication error

Perform the authentication or register as a user, and then perform the printing again.

[4042] Department authentication error

Check department information registered in this equipment.

[4045] Problem in LDaP server connection or LDaP server authorization settings

Confirm the administrator for the LDAP server connection or LDAP server authorization

settings.

[4111] Quota over error (The number of the assigned pages set by department and user

management has reached 0.)

The number of the assigned pages set by the department and the number of those assigned
by user management have both reached 0. Assign the number of the pages again or perform
initialization.

[4112] Quota over error (The number of the assigned pages set by user management has

reached 0.)

The number of the assigned pages set by the user management has reached 0. Assign the
number of the pages again or perform initialization.

[4113] Quota over error (The number of the assigned pages set by department

management has reached 0.)

The number of the assigned pages set by the department management has reached 0.
Assign the number of the pages again or perform initialization.

[4121] Job canceling due to external counter error

1.  Drop a coin in. Perform the print job in error again.
2.  Insert a key card and then perform the print job in error again, or consult your administrator.
3.  Insert a key copy counter and then perform the print job in error again.
4.  Reset the scheduled print job and then perform the print job in error again.

[4211] Printing data storing limitation error

Select “Normal Print”, and then perform the printing again.

[4212] e-Filing storing limitation error

Select “Normal Print”, and then perform the printing again.

«
...
160
161
162
163
164
...
»

Summary of Contents for MB760







































































































































































































































































































































































































Reviews:

No comments

Related manuals for MB760

Brand: Canon Pages: 29

PIXMA MX410 Series

Brand: Canon Pages: 46

Brand: Canon Pages: 65

Brand: Canon Pages: 4

Brand: Canon Pages: 2

Brand: Canon Pages: 2

Sure shot 80 tele

Brand: Canon Pages: 39

BJC6500 - BJC 6500 Color Inkjet Printer

Brand: Canon Pages: 6

Brand: Canon Pages: 20

imagePROGRAF iPF6450

Brand: Canon Pages: 35

PIXMA MX340 Series

Brand: Canon Pages: 11

PIXMA MX340 Series

Brand: Canon Pages: 16

imagePROGRAF iPF6300S

Brand: Canon Pages: 12

Brand: Canon Pages: 19

Brand: Canon Pages: 101

iP4700 - PIXMA Color Inkjet Printer

Brand: Canon Pages: 28

Brand: Canon Pages: 2

Brand: Canon Pages: 35

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands