Oki MB760 Service Manual Download

Page: 25 / 390

45641001TH Rev.1

3-2 /

Oki Data CONFIDENTIAL

Note:

Do not enter any of the modes shown below since they are provided only for production. If you

do so, the equipment may not be restarted.

[2]+[CLEAR]+[POWER]
[7]+[CLEAR]+[POWER]
[8]+[CLEAR]+[POWER]
[9]+[CLEAR]+[POWER]

[D] state transition diagram of self-diagnosis modes

Authentication

screen

Normal

Warming up

Ready

[POWER]

OFF

To user

Each mode

Self-diagnosis

mode

[POWER]

Fig. 3-1

*1 If you have used a self-diagnostic mode, turn the power OFF before the customer starts using

the equipment

*2 Mode shown in the table “[C] List of modes”

[e] about each mode

• Control panel check mode (01)

Operation procedure

[0][1]

[POWER]

LED lit/

LCD blinking

[START]

(Button check)

[POWER] OFF/ON

(Exit)

Notes:

• A mode can be cancelled by [POWER] OFF/ON when the LED is lit and the LCD is blinking.

•  Button Check
  Buttons with LED: Press to turn OFF the LED.
  Buttons without LED: Press to display the message on the control panel.

Button on touch panel: Press to display the initial screen displayed at power-ON. Press

[execution] on the touch panel and then the [CLEAR] button on the control panel. The

screen then returns to the Button Check menu.

Summary of Contents for MB760







































































































































































































































































































































































































Search results

Summary of Contents for MB760

Reviews:

Related manuals for MB760

Brands by name

Popular brands

Oki MB760, Service Manual

Search results

Summary of Contents for MB760

Reviews:

Related manuals for MB760

Brands by name

Popular brands