manualshive.com logo in svg

ODA LF Series, User Manual, Page: 89 / 116

Share
Download
ODA LF Series User Manual Download Page 89

▌Auto Key Lock can be used if a user doesn't use the key for a long time.

AUTO_KEY_LOCK

 

▌Power on while pressing DYN SETTING,FACTORY key.

 

▌Power ON

▌Release the key after model name is displayed and entered 
  "--- FACTORY ---" mode.

▌Move to AUTO_KEY_LOCK menu using cursor key.
"8.AUTO_KEY_LOCK" will be displayed.

FACTORY menu order: 1.USER_CLEAR ↔ 2.CAL_RESTORE ↔ 3.CAL_BACKUP ↔ 

4.CAL_DEFAULT ↔ 5.LOAD_DEFAULT ↔ 6.DELIMITER_CHAR ↔

7.COM_RESPONSE ↔ 8.AUTO_KEY_LOCK ↔ 9.ADC_SAMPLING   

 

▌Press DYN SETTING,FACTORY key.
Enter COM_RESPONSE menu.
"A.LOCK" will be displayed on 2nd line.

▌Set AUTO_KEY_LOCK using cursor key.

AUTO_KEY_LOCK menu order: 1.DISABLE ↔ 2.ENABLE
 ※ 1.DISABLE 2.ENABLE

 

▌Press DYN SETTING,FACTORY key.
 After saving COM_RESPONS setting, return to FACTORY menu.

▌Power OFF

 Note

When AUTO KEY LOCK is on, key will be locked if there's no key operation for tens of seconds.

Press and hold

Release

 -  80  - 

5-10. AUTO_KEY_LOCK

DYN SETTING

FACTORY

POWER

DYN SETTING

FACTORY

POWER

DYN SETTING

FACTORY

DYN SETTING

FACTORY

Summary of Contents for LF Series





















































































































Reviews:

No comments