Nuvoton Mini57 Series Technical Reference Manual Download Page 13

Page: 13 / 475

Mini57

Apr. 06, 2017

Page 13 of 475

Rev.1.00

MINI5

RI
E

TECH

NIC

L R

RE
N

CE
MA
N

2 FEATURES



Core

ARM® Cortex® -M0 core running up to 48 MHz

One 24-bit system timer

Supports low power Idle mode

A single-cycle 32-bit hardware multiplier

NVIC for the 32 interrupt inputs, each with 4-level of priority

Supports Serial Wire Debug (SWD) interface and two watchpoints/four
breakpoints



Built-in LDO for wide operating voltage ranged: 2.1V to 5.5V



Memory

29.5 Kbytes Flash memory for program memory (APROM)

Configurable Flash memory for data memory (Data Flash)

2 KB Flash memory for loader (LDROM)

Three 0.5 KB Flash memory for security protection (SPROM)

4 KB SRAM for internal scratch-pad RAM (SRAM)



Clock Control

Programmable system clock source



Switch clock sources on-the-fly

4 ~ 24 MHz external crystal input (HXT)

32.768 kHz external crystal input (LXT) for idle wake-up and system operation
clock

48 MHz internal oscillator (HIRC) (±1% accuracy at 25

C, 5V)



Dynamically calibrating the HIRC OSC to 48 MHz ±1% from -40

℃

to 105

℃

by external 32.768K crystal oscillator (LXT)

10 kHz internal low-power oscillator (LIRC) for Watchdog Timer and idle wake-
up



I/O Port

Up to 22 general-purpose I/O (GPIO) pins and 1 Reset pin for QFN-33 package

Four I/O modes:



Quasi-bidirectional input/output



Push-Pull output



Open-Drain output



Input only with high impendence

Optional TTL/Schmitt trigger input

I/O pin can be configured as interrupt source with edge/level setting

Supports high driver and high sink I/O mode

Summary of Contents for Mini57 Series




























































































































































































































































































































































































































































































Search results

Summary of Contents for Mini57 Series

Reviews:

Brands by name

Popular brands

Nuvoton Mini57 Series, Technical Reference Manual

Search results

Summary of Contents for Mini57 Series

Reviews:

Brands by name

Popular brands