NORTHROP GRUMMAN Sperry Marine NAVIGAT X MK 2 Assembly Instructions Manual Download Page 90

Page: 90 / 112

056341 Rev. AA

NAVIGAT X Mk 2

Page 8-20

8: Gyroshpere Installation and Service

Take the new exchange gyrosphere from its carrying box and place it on
the plastic bowl from the installation parts kit

Proceed with the installation of the gyrosphere into the gyrosphere con-
tainer, as described under 8.3.1, from step 10 onwards.

Carefully put the gyrosphere between
the foam rubber pads in its carrying box.

Pack the box in the original transport
container for returning to Sperry Marine.

Note

Make sure to include the gyrosphere service report when returning a sphere to
Sperry Marine.
When the service report is not returned, no warranty exchange of the gyro-
sphere is possible.

Summary of Contents for Sperry Marine NAVIGAT X MK 2
















































































































Search results

Summary of Contents for Sperry Marine NAVIGAT X MK 2

Reviews:

Related manuals for Sperry Marine NAVIGAT X MK 2

Brands by name

Popular brands

NORTHROP GRUMMAN Sperry Marine NAVIGAT X MK 2, Assembly Instructions Manual

Search results

Summary of Contents for Sperry Marine NAVIGAT X MK 2

Reviews:

Related manuals for Sperry Marine NAVIGAT X MK 2

Brands by name

Popular brands