NORTHROP GRUMMAN Sperry Marine NAVIGAT X MK 2 Assembly Instructions Manual Download Page 4

Page: 4 / 112

056341 Rev. AA

NAVIGAT X Mk 2

3 Errors and Alarms

3.1

Alarm Indication .................................................................................................. 3–1

3.1.1

Audible Alarm Indication ......................................................................... 3–1

Invalid Function ................................................................................ 3–1
System Alarm ................................................................................... 3–1

3.1.2

Visual Alarm Indication............................................................................ 3–1

3.1.3

Acknowledging Alarms / Muting the Audible Alarm............................. 3–1

3.2

Error Messages .................................................................................................... 3–2

3.3

Service Info Menu (Service Setup 2).................................................................. 3–3

3.3.1

Service Setup 2 – Access Code ............................................................... 3–3

3.3.2

Service Setup 2 – Overview..................................................................... 3–3

3.3.3

Service Setup 2 – Parameters.................................................................. 3–4

4 Preventive Maintenance

4.1

Maintenance Specifications................................................................................ 4–1

4.1.1

Gyrosphere Maintenance ........................................................................ 4–1

4.1.2

Five-Year Maintenance ............................................................................ 4–1

4.1.3

System Software Updates ....................................................................... 4–1

4.2

Maintenance by Shipboard Personnel............................................................... 4–2

4.2.1

Protecting the Gyrosphere from Low Ambient Temperatures ............. 4–2

4.2.2

Removing the gyrosphere container from the compass housing........ 4–3

4.2.3

Re-installing the gyrosphere container in the compass housing ......... 4–5

4.2.4

Power-up Function Test ........................................................................... 4–7

4.3

Maintenance by Service Personnel.................................................................... 4–9

4.3.1

Gyrosphere Installation and Service....................................................... 4–9

4.3.2

Updating the System Software ............................................................... 4–9

5 Installation

5.1

Installing the Compass Housing......................................................................... 5–1

5.2

Electrical Installation ........................................................................................... 5–2

5.3

Gyrosphere Installation....................................................................................... 5–2

5.4

Initial System Configuration ............................................................................... 5–3

5.4.1

Alignment Error Correction ..................................................................... 5–5

5.4.2

Magnetic Compass Calibration ............................................................... 5–6

Summary of Contents for Sperry Marine NAVIGAT X MK 2
















































































































Search results

Summary of Contents for Sperry Marine NAVIGAT X MK 2

Reviews:

Related manuals for Sperry Marine NAVIGAT X MK 2

Brands by name

Popular brands

NORTHROP GRUMMAN Sperry Marine NAVIGAT X MK 2, Assembly Instructions Manual

Search results

Summary of Contents for Sperry Marine NAVIGAT X MK 2

Reviews:

Related manuals for Sperry Marine NAVIGAT X MK 2

Brands by name

Popular brands