NORTHROP GRUMMAN Sperry Marine NAVIGAT X MK 2 Assembly Instructions Manual Download Page 83

Page: 83 / 112

NAVIGAT X Mk 2

056341 Rev. AA

8: Gyroshpere Installation and Service

Page 8-13

Put both hands around the container and
lift it up, so that the coupling tongues
disengage from their seats in the bayo-
net.

While supporting the container with both
palms, put the thumbs on the rim of the
collar and turn the collar to the left.

Gently lower the container. The cou-
pling tongues slide down in the grooves
of the bayonet and the container is re-
leased from the collar.

Carefully take the container out of the housing and carry it to the storage
or work place.

10) Put the door in front of the housing and connect the grounding strap.

11)

Fit the door back on the housing and tighten the retaining screws.

Summary of Contents for Sperry Marine NAVIGAT X MK 2
















































































































Search results

Summary of Contents for Sperry Marine NAVIGAT X MK 2

Reviews:

Related manuals for Sperry Marine NAVIGAT X MK 2

Brands by name

Popular brands

NORTHROP GRUMMAN Sperry Marine NAVIGAT X MK 2, Assembly Instructions Manual

Search results

Summary of Contents for Sperry Marine NAVIGAT X MK 2

Reviews:

Related manuals for Sperry Marine NAVIGAT X MK 2

Brands by name

Popular brands