NORTHROP GRUMMAN Sperry Marine NAVIGAT X MK 2 Assembly Instructions Manual Download Page 62

Page: 62 / 112

056341 Rev. AA

NAVIGAT X Mk 2

Page 6-10

6: System Configuration

6.1.3.5

Align Err. Corr.

6.1.3.6

Shaft Cor. Angle

6.1.3.7

Gen. Alarm Setup

Hdg. Sel.

Function:

Sets the heading reference selector

Settings: CDU 1

The heading reference is selected using the gyro’s control and dis-
play unit

COMP. MON

The heading reference is selected from a NAVITWIN III compass
monitor

AUTOPILOT

The heading reference is selected from a NAVIPILOT heading con-
trol system

EXT.SEL.

The heading reference is selected using an external selector switch

Function:

Sets the alignment error correction value

Range:

-179.9 – +180.0 °

Function:

Sets the shaft encoder correction value

Range:

-179.9 – +180.0 °

Function:

Sets the conditions for actuation of the alarm relay

Settings: ON ALL ALARMS

The relay is actuated on any alarm condition.

ON FATAL ALARMS

The relay is actuated on fatal alarm conditions only. A fatal alarm
exists when the gyrocompass can no longer provide its own head-
ing data. Loss of external data and the heading difference alarm are
non-fatal alarm conditions.

Summary of Contents for Sperry Marine NAVIGAT X MK 2
















































































































Search results

Summary of Contents for Sperry Marine NAVIGAT X MK 2

Reviews:

Related manuals for Sperry Marine NAVIGAT X MK 2

Brands by name

Popular brands

NORTHROP GRUMMAN Sperry Marine NAVIGAT X MK 2, Assembly Instructions Manual

Search results

Summary of Contents for Sperry Marine NAVIGAT X MK 2

Reviews:

Related manuals for Sperry Marine NAVIGAT X MK 2

Brands by name

Popular brands