NORTHROP GRUMMAN Sperry Marine NAVIGAT X MK 2 Assembly Instructions Manual Download Page 79

Page: 79 / 112

NAVIGAT X Mk 2

056341 Rev. AA

8: Gyroshpere Installation and Service

Page 8-9

Gently lower the container. The cou-
pling tongues engage into their seats in
the bayonet and the container is locked
in place by gravity.

Plug the gyrosphere supply and phase
bridge connector into its socket on the
gyrosphere container.

10) Check that the gyrosphere container can

be freely and smoothly turned around
the vertical axis.

11)

Put the door in front of the housing, so
that the keypad can be operated. If the
pad has been disconnected during gyro-
sphere installation, reconnect the ribbon
cable to connector J 4 on the main PCB.

12) The compass is now ready to be put into operation for the power-up func-

tion test. To observe the correct working of the follow-up circuit, the hous-
ing may be left open during the run-up phase.

Summary of Contents for Sperry Marine NAVIGAT X MK 2
















































































































Search results

Summary of Contents for Sperry Marine NAVIGAT X MK 2

Reviews:

Related manuals for Sperry Marine NAVIGAT X MK 2

Brands by name

Popular brands

NORTHROP GRUMMAN Sperry Marine NAVIGAT X MK 2, Assembly Instructions Manual

Search results

Summary of Contents for Sperry Marine NAVIGAT X MK 2

Reviews:

Related manuals for Sperry Marine NAVIGAT X MK 2

Brands by name

Popular brands