NORTHROP GRUMMAN Sperry Marine NAVIGAT X MK 2 Assembly Instructions Manual Download Page 57 | Manualshive

Page: 57 / 112

background image

NAVIGAT X Mk 2

056341 Rev. AA

6: System Configuration

Page 6-5

6.1.3

Service Setup 1 – Parameters

6.1.3.1

Interface I/O

Mag. Hdg. Inp.

Function:

Selects the data protocol for the magnetic heading input.

Settings: NMEA-HDM

Magnetic heading is read from the NMEA $--HDM sentence.

NMEA-HCHDT

Magnetic heading is read from the NMEA $HCHDT sentence

NMEA-HDG

Magnetic heading is read from the NMEA $--HDG sentence

PLATH-MAGN

Magnetic heading is read from a magnetic heading message in the
PLATH binary format

NAVIPILOT

Magnetic heading is read from the binary repeater data message
received from a NAVIPILOT heading control system

COMP. MONITOR

Magnetic heading is read from the data received at the Compass
Monitor input

OFF

The magnetic heading input is disabled

Speed Input

Function:

Selects the speed data input

Settings: 200 Pulse/NM

Speed is received as a 200 Pulse/NM signal at the 200 Pulse/NM
input

NMEA

Speed is read from the NMEA speed protocol(s) received at the
NMEA speed input

Note

If NMEA speed input is used and more than one valid type of speed sentence is
received, the input is evaluated in the following order: VBW ground speed,
VBW water speed, VHW, VTG.
If speed is received using the VBW sentence, only the longitudinal speed com-
ponent is evaluated for automatic North speed error correction.

«
...
55
56
57
58
59
...
»

Summary of Contents for Sperry Marine NAVIGAT X MK 2

















































































































Reviews:

No comments

Related manuals for Sperry Marine NAVIGAT X MK 2

Brand: Facom Pages: 42

Brand: JGR Pages: 12

Brand: MADDALENA Pages: 4

Brand: Macnaught Pages: 4

Brand: Waterproof Pages: 10

Brand: Ocean Optics Pages: 43

Brand: Ocean Technology Systems Pages: 12

Brand: Ocean Reef Pages: 24

Brand: Yamaha Pages: 14

Disklavier Mark II XG Series

Brand: Yamaha Pages: 12

Brand: +GF+ Pages: 8

Brand: SOMFY Pages: 40

Brand: Badger Meter Pages: 24

Brand: E+E Elektronik Pages: 20

Brand: Brooks Pages: 64

Brand: brena Pages: 26

Brand: QuantAsylum Pages: 35

Brand: R&S Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands