NORTHROP GRUMMAN Sperry Marine NAVIGAT X MK 2 Assembly Instructions Manual Download Page 77

Page: 77 / 112

NAVIGAT X Mk 2

056341 Rev. AA

8: Gyroshpere Installation and Service

Page 8-7

28) Close the ventilation hole with the plug.

29) Carefully dry the outside of the gyro-

sphere container with a lint-free cloth.

30) Connect the power cable to the centering

pin.

31) Affix the provided labels with the gyro-

sphere's serial number and the wheel-
mark logo to the outside of the gyro-
sphere container.

32) Insert the base contact plug through the

cutout in the lower section of the con-
tainer. Connect the plug to the base con-
tact.

33) The gyrosphere container is now ready

to be installed in the compass housing.

Summary of Contents for Sperry Marine NAVIGAT X MK 2
















































































































Search results

Summary of Contents for Sperry Marine NAVIGAT X MK 2

Reviews:

Related manuals for Sperry Marine NAVIGAT X MK 2

Brands by name

Popular brands

NORTHROP GRUMMAN Sperry Marine NAVIGAT X MK 2, Assembly Instructions Manual

Search results

Summary of Contents for Sperry Marine NAVIGAT X MK 2

Reviews:

Related manuals for Sperry Marine NAVIGAT X MK 2

Brands by name

Popular brands