NORTHROP GRUMMAN Sperry Marine NAVIGAT X MK 2 Assembly Instructions Manual Download Page 64

Page: 64 / 112

056341 Rev. AA

NAVIGAT X Mk 2

Page 6-12

6: System Configuration

6.2 Factory Settings Menu (Technical Pages)

The Technical Pages provide access to a number of factory-set parameters
which need not normally be altered. However, should the system software need
to be exchanged, these settings will be lost and must be re-entered manually.

6.2.1

Technical Pages – Access Code

To prevent inadvertent or unauthorized changes to the system configuration, all
service setup menus are protected by access codes.

6.2.2

Technical Pages – Overview

From the main menu screen, go to „Setup Menu / Service Setup“:

To access the Technical Pages, enter code

140.

ENTER SETUP CODE

SERVICE SETUP

000

TECHNICAL PAGES

F1 SOFTWARE VERSION

F2 UPDATE SOFTWARE

F3 CORRECTION VAL.

SOFTWARE VERSION

UPDATE SOFTWARE

CORRECTION VAL.

HARDWARE:

main PCB revision

SW. VER

software creation date

MASTERBOARD:

system software version

gyro current gain:

0.000 – 9.999

corr. value temp..:

-99 – +99 ˚C

update software via service interface
(factory use only, not for field service)

DISPLAY BOARD:

ext. display software version

software version info

in-circuit software update

corr. values for temperature

and gyro current

Summary of Contents for Sperry Marine NAVIGAT X MK 2
















































































































Search results

Summary of Contents for Sperry Marine NAVIGAT X MK 2

Reviews:

Related manuals for Sperry Marine NAVIGAT X MK 2

Brands by name

Popular brands

NORTHROP GRUMMAN Sperry Marine NAVIGAT X MK 2, Assembly Instructions Manual

Search results

Summary of Contents for Sperry Marine NAVIGAT X MK 2

Reviews:

Related manuals for Sperry Marine NAVIGAT X MK 2

Brands by name

Popular brands