NORTHROP GRUMMAN Sperry Marine NAVIGAT X MK 2 Assembly Instructions Manual Download Page 3

Page: 3 / 112

NAVIGAT X Mk 2

056341 Rev. AA

Contents

Safety Precautions

1 Description

1.1

Design and Main Features................................................................................... 1–1

1.2

Data and Signal Interfaces .................................................................................. 1–2

1.3

Technical Data ...................................................................................................... 1–3

2 Operation

2.1

Operating Conditions........................................................................................... 2–1

2.2

Power-up Sequence............................................................................................. 2–1

2.3

Display and Control Elements............................................................................. 2–2

2.3.1

Control and Display Unit .......................................................................... 2–2

2.3.2

External Control Devices .......................................................................... 2–2

2.4

Selecting the Heading Reference........................................................................ 2–3

2.4.1

Selection from the Control and Display Unit.......................................... 2–3

2.4.2

Selection from the Compass Monitor ..................................................... 2–3

2.4.3

Selection via external selector switch ..................................................... 2–3

2.5

Adjusting the Display Brightness ....................................................................... 2–4

2.6

Acknowledging Alarms / Muting the Audible Alarm ........................................ 2–4

2.7

Optional Functions............................................................................................... 2–4

2.7.1

Acknowledging Alarms Remotely ........................................................... 2–4

2.8

Operating Menu ................................................................................................... 2–5

2.8.1

Entering / Quitting the Main Menu .......................................................... 2–5

2.8.2

Navigating the Menu ................................................................................ 2–5

2.8.3

Selecting Parameter Settings .................................................................. 2–6

2.8.4

Editing Parameter Values ......................................................................... 2–6

2.9

Display Data Menu............................................................................................... 2–7

2.10

Manual Settings Menu ........................................................................................ 2–8

2.10.1

Manual Settings – Overview .................................................................... 2–8

2.10.2

Manual Settings – Parameters ................................................................. 2–9

2.11

User Setup .......................................................................................................... 2–15

2.11.1

User Setup – Overview ........................................................................... 2–15

2.11.2

User Setup – Parameters........................................................................ 2–16

Date/Time ........................................................................................ 2–16
Software Version ............................................................................ 2–17
Magnetic Compass Calibration Table ........................................... 2–17

Summary of Contents for Sperry Marine NAVIGAT X MK 2
















































































































Search results

Summary of Contents for Sperry Marine NAVIGAT X MK 2

Reviews:

Related manuals for Sperry Marine NAVIGAT X MK 2

Brands by name

Popular brands

NORTHROP GRUMMAN Sperry Marine NAVIGAT X MK 2, Assembly Instructions Manual

Search results

Summary of Contents for Sperry Marine NAVIGAT X MK 2

Reviews:

Related manuals for Sperry Marine NAVIGAT X MK 2

Brands by name

Popular brands