manualshive.com logo in svg

Nortel Passport 7400, Hardware Installation, Maintenance, And Troubleshooting, Page: 231 / 438

Share
Download
Nortel Passport 7400 Hardware Installation, Maintenance, And Troubleshooting Download Page 231

Chapter 37 Hardware procedures   231

Passport 7400 Hardware Installation, Maintenance, and Upgrade 5.2S1

Installing a blank processor card

Install a blank processor card in each empty slot on a shelf in order to meet
electromagnetic interference (EMI) regulatory requirements and thermal
specifications.

Prerequisites

•

You will need a blank processor card with PEC NTBP23.

Procedure steps

1

Unpack the blank processor card. Keep the packaging materials for future
use.

2

Pull open the top and bottom latches of the blank processor card and slide
it into the slot until the locking latches begin to close.

3

Close and lock the latches. See the figure “Locking and unlocking
processor card latches” (page 239).

Summary of Contents for Passport 7400























































































































































































































































































































































































































































Reviews:

No comments