manualshive.com logo in svg

Nortel Passport 7400, Hardware Installation, Maintenance, And Troubleshooting, Page: 215 / 438

Share
Download
Nortel Passport 7400 Hardware Installation, Maintenance, And Troubleshooting Download Page 215

Chapter 37 Hardware procedures   215

Passport 7400 Hardware Installation, Maintenance, and Upgrade 5.2S1

Installing a 5-slot Passport switch in a rack or cabinet

Install a 5-slot Passport switch in a rack or cabinet using brackets that bolt into
the side rails of the rack or cabinet.

Prerequisites

•

If you plan to install the switch in a Passport cabinet, check the position
of the uprights. You must set the front uprights back 11.4 cm (4.5 in.)
from the front of the cabinet. The spacing between front and rear uprights
must be 36.8 cm (14.5 in.).

•

Install and ground the rack or cabinet before proceeding. For more
information, see “Cabinet installation” (page 81).

Procedure steps

1

Secure the left and right rack-mounting brackets to the rack. Insert the
4 screws into the holes in each bracket and into the respective holes in
the rack. Then, fasten the screws. See the figure “Securing the rack-
mounting brackets to a rack” (page 216).

2

Secure the rack-mounting crossmember to the rear of the rack-mounting
brackets with the 2 screws provided. See the figure “Securing the rack-
mounting brackets to a rack” (page 216).

3

Place the switch on the rack-mounting brackets. Use the 2 remaining
screws to fasten the switch to the right-hand bracket. Ensure that the rear
of the switch is fully seated on the rack-mount brackets. See the figure
“Securing the switch to a rack” (page 217).

Summary of Contents for Passport 7400























































































































































































































































































































































































































































Reviews:

No comments