Nortel Passport 7400 Hardware Installation, Maintenance, And Troubleshooting Download Page 148

Page: 148 / 438

148 Chapter 31 Passport cabinet door removal and installation

241-7401-240 5.2S1

Figure 40
Passport cabinet door removal and installation task flow

Task flow navigation

•

“Removing a Passport cabinet door alarm cable” (page 368)

•

“Removing a Passport cabinet door” (page 367)

•

“Moving a door hinge to the other side of a cabinet” (page 304)

•

“Installing a Passport cabinet door” (page 246)

•

“Installing a Passport cabinet door alarm cable” (page 247)

Yes

Passport cabinet

door removal and

installation

Removing a

Passport cabinet

door alarm cable

Removing a

Passport cabinet

door

move hinge to

other side?

Installing a

Passport cabinet

door

Installing a

Passport cabinet

door alarm cable

Moving a door

hinge to the other

side of a cabinet

End

PP_TASK_1029.ins

Summary of Contents for Passport 7400























































































































































































































































































































































































































































Search results

Summary of Contents for Passport 7400

Reviews:

Nortel Passport 7400, Hardware Installation, Maintenance, And Troubleshooting, Page: 148 / 438

Search results

Summary of Contents for Passport 7400

Reviews: