Nortel 2500 Seriess System Configuration Manual Download Page 96 | Manualshive

Page: 96 / 392

background image

96

CLI Basics

Parameters
and variables

Description

force

Instructs the switch to skip the shutdown confirmation
prompt.

minutes-to-wait
<1-80>

Specifies the number of minutes that pass before the
switch resets itself. The default wait time is set at 10
minutes.

ATTENTION

Any configurations or login performed on the switch after the shutdown command
is initiated are not saved to NVRAM and are lost after the reset.

The

shutdown

command is executed in the Privileged EXEC command

mode.

Managing basic system information

This section shows you how to view basic system information such as
the current software version. This section contains information about the
following topics:

•

"show sys-info command" (page 96)

•

"show tech command" (page 97)

show sys-info command

The

show sys-info

command displays the current system characteristics.

The syntax for the

show sys-info

command is:

show sys-info

The

show sys-info

command is executed in the Privileged EXEC

command mode.

The

show sys-info

command has no parameters or variables.

Figure 25 "show sys-info command output" (page 97)

displays sample

output from the show sys-info command.

Nortel Ethernet Routing Switch 2500 Series

Overview — System Configuration

NN47215-500 (323162-B)

02.02

Standard

4.1

19 November 2007

Copyright © 2007, Nortel Networks

.

«
...
94
95
96
97
98
...
»

Summary of Contents for 2500 Seriess









































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2500 Seriess

Brand: Patton electronics Pages: 8

COMSPHERE 3800 Series

Brand: Paradyne Pages: 88

COMSPHERE 3800PLUS

Brand: Paradyne Pages: 5

Brand: Paradyne Pages: 2

Brand: iDirect Pages: 52

Brand: Idis Pages: 31

Brand: ZyXEL Communications Pages: 244

Brand: Grundig Pages: 24

InnoMedia MTA 3328-2R

Brand: VoiceLine Pages: 18

FlexNetwork 5130 Series

Brand: HPE Pages: 33

ExpressBox2 EB2

Brand: Magma Pages: 74

Brand: Paradyne Pages: 6

PSoC 4 S Series

Brand: Cypress Pages: 4

LMP-1202G-SFP Series

Brand: ANTAIRA Pages: 19

Brand: Alarm Pages: 5

FiberTwist G6426

Brand: Genexis Pages: 9

Brand: Razer Pages: 17

Brand: Topcom Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands