Nortel 2500 Seriess System Configuration Manual Download Page 180

Page: 180 / 392

180

System configuration using the CLI

The

no ip netmask

command is executed in the Global Configuration

command mode.

The

no ip netmask

command has no parameters or variables .

ip default-gateway command

The

ip default-gateway

command sets the IP default gateway address

for a switch. The syntax for the

ip default-gateway

command is:

ip default-gateway <XXX.XXX.XXX.XXX>

The

ip default-gateway

command is executed in the Global

Configuration command mode.

Table 48 "ip default-gateway command parameters and variables" (page
180)

describes the parameters and variables for the

ip default-gateway

command.

Table 48
ip default-gateway command parameters and variables

Parameters and
variables

Description

XXX.XXX.XXX.XXX

Enter the dotted-decimal IP address of the default IP
gateway.

ATTENTION

When you change the IP gateway, you may lose connection to Telnet and the Web.

no ip default-gateway command

The

no ip default-gateway

command sets the IP default gateway

address to zeros (0). The syntax for the

no ip default-gateway

command is:

no ip default-gateway

The

no ip default-gateway

command is executed in the Global

Configuration command mode.

The

no ip default-gateway

command has no parameters or variables.

ATTENTION

When you change the IP gateway address, you may lose connection to Telnet and
the Web. You also may disable any new Telnet connection required to connect to
the serial Console port to configure a new IP Gateway address.

Nortel Ethernet Routing Switch 2500 Series

Overview — System Configuration

NN47215-500 (323162-B)

02.02

Standard

4.1

19 November 2007

Summary of Contents for 2500 Seriess






































































































































































































































































































































































































Search results

Summary of Contents for 2500 Seriess

Reviews:

Related manuals for 2500 Seriess

Brands by name

Popular brands

Nortel 2500 Seriess, System Configuration Manual

Search results

Summary of Contents for 2500 Seriess

Reviews:

Related manuals for 2500 Seriess

Brands by name

Popular brands