Nortel 2500 Seriess System Configuration Manual Download Page 221

Page: 221 / 392

Configuring LLDP using the CLI

221

lldp tx-tlv command

The

lldp tx-tlv

command specifies the optional TLVs to include in the

transmitted LLDPDUs. The syntax for the

lldp tx-tlv

command is:

lldp tx-tlv [port <portlist>] [local-mgmt-addr] [port-desc]

[sys-cap] [sys-desc] [sys-name]

The

lldp tx-tlv

command is executed in the Interface Configuration

command mode.

Table 81 "lldp tx-tlv command parameters and variables" (page
221)

describes the parameters and variables for the lldp tx-tlv command.

Table 81
lldp tx-tlv command parameters and variables

Parameters and
variables

Description

port

<portlist>

Specifies the ports affected by the command.

local-mgmt-addr

Local management address TLV

port-desc

Port description TLV

sys-cap

System capabilities TLV

sys-desc

System description TLV

sys-name

System name TLV

no lldp tx-tlv command

The

no lldp tx-tlv

command specifies the optional TLVs not to include

in the transmitted LLDPDUs. The syntax for the

lldp tx-tlv

command is:

no lldp tx-tlv [port <portlist>] [local-mgmt-addr]

[port-desc]

[sys-cap] [sys-desc] [sys-name]

The

no lldp tx-tlv

command is executed in the Interface Configuration

command mode.

Table 82 "no lldp tx-tlv command parameters and variables" (page
221)

describes the parameters and variables for the no lldp tx-tlv command.

Table 82
no lldp tx-tlv command parameters and variables

Parameters and
variables

Description

port

<portlist>

Specifies the ports affected by the command.

local-mgmt-addr

Local management address TLV

Nortel Ethernet Routing Switch 2500 Series

Overview — System Configuration

NN47215-500 (323162-B)

02.02

Standard

4.1

19 November 2007

Summary of Contents for 2500 Seriess






































































































































































































































































































































































































Search results

Summary of Contents for 2500 Seriess

Reviews:

Related manuals for 2500 Seriess

Brands by name

Popular brands

Nortel 2500 Seriess, System Configuration Manual

Search results

Summary of Contents for 2500 Seriess

Reviews:

Related manuals for 2500 Seriess

Brands by name

Popular brands