Nortel 2500 Seriess System Configuration Manual Download Page 210

Page: 210 / 392

210

System configuration using the CLI

Table 69 "sntp server primary address command parameters and variables"
(page 210)

describes the parameters and variables for the sntp server

primary address command.

Table 69
sntp server primary address command parameters and variables

Parameters and
variables

Description

<A.B.C.D>

Enter the IP address of the primary NTP server.

The default is 0.0.0.0.

sntp server secondary address command

The

sntp server secondary address

command specifies the IP

addresses of the secondary NTP server. The syntax for the

sntp server

secondary address

command is:

sntp server secondary address <A.B.C.D>

The

sntp server secondary address

command is executed in the

Global Configuration command mode.

Table 70 "sntp server secondary address command parameters and
variables" (page 210)

describes the parameters and variables for the sntp

server secondary address command.

Table 70
sntp server secondary address command parameters and variables

Parameters and
variables

Description

<A.B.C.D>

Enter the IP address of the secondary NTP server.

The default is 0.0.0.0.

no sntp server command

The

no sntp server

command clears the NTP server IP addresses. The

syntax for the

no sntp server

command is:

no sntp server <primary|secondary>

The

no sntp server

command is executed in the Global Configuration

command mode.

Table 71 "no sntp server command parameters and variables" (page
211)

describes the parameters and variables for the no sntp server

command.

Nortel Ethernet Routing Switch 2500 Series

Overview — System Configuration

NN47215-500 (323162-B)

02.02

Standard

4.1

19 November 2007

Summary of Contents for 2500 Seriess






































































































































































































































































































































































































Search results

Summary of Contents for 2500 Seriess

Reviews:

Related manuals for 2500 Seriess

Brands by name

Popular brands

Nortel 2500 Seriess, System Configuration Manual

Search results

Summary of Contents for 2500 Seriess

Reviews:

Related manuals for 2500 Seriess

Brands by name

Popular brands