Nortel 2500 Seriess System Configuration Manual Download Page 209

Page: 209 / 392

Setting time on network elements using Simple Network Time Protocol

209

Figure 73
show sntp command output

sntp enable command

ATTENTION

The default setting for SNTP is disabled.

The

sntp enable

command enables SNTP. The syntax for the

sntp

enable

command is:

sntp enable

The

sntp enable

command is executed in the Global Configuration

command mode.

The

sntp enable

command has no parameters or variables.

no sntp enable command

The

no sntp enable

command disables SNTP. The syntax for the

sntp enable

command is:

no sntp enable

The

no sntp enable

command is executed in the Global Configuration

command mode.

The

no sntp enable

command has no parameters or variables.

sntp server primary address command

The

sntp server primary address

command specifies the IP

addresses of the primary NTP server. The syntax for the

sntp server

primary address

command is:

sntp server primary address <A.B.C.D>

The

sntp server primary address

command is executed in the

Global Configuration command mode.

Nortel Ethernet Routing Switch 2500 Series

Overview — System Configuration

NN47215-500 (323162-B)

02.02

Standard

4.1

19 November 2007

Summary of Contents for 2500 Seriess






































































































































































































































































































































































































Search results

Summary of Contents for 2500 Seriess

Reviews:

Related manuals for 2500 Seriess

Brands by name

Popular brands

Nortel 2500 Seriess, System Configuration Manual

Search results

Summary of Contents for 2500 Seriess

Reviews:

Related manuals for 2500 Seriess

Brands by name

Popular brands