Nortel 2500 Seriess System Configuration Manual Download Page 360

Page: 360 / 392

360

Appendix D Command List

Command

Page No.

no autotopology

"no autotopology command" (page 216)

no-banner

"no banner command" (page 202)

no clock summer-time

"no clock summer-time" (page 214)

no clock time-zone

"no clock time-zone" (page 213)

no command

"no command" (page 90)

no eapol guest-vlan [enable]

Nortel Ethernet Routing Switch 2500 Series
Security — Configuration and Management
(NN47215-505)

no flowcontrol [port <portlist>]

"no autotopology command" (page 216)

no ip address

"no ip address command" (page 179)

no ip bootp server

"no ip bootp server command" (page 197)

no ip default-gateway

"no ip default-gateway command" (page 180)

no ip domain-name

"no ip domain-name command" (page 188)

no ip name-server <A.B.C.D>

"no ip name-server command" (page 187)

no ip netmask

"no ip netmask command" (page 179)

no ipmgr {source-ip [<1-10>]}

Nortel Ethernet Routing Switch 2500 Series
Security — Configuration and Management
(NN47215-505)

no ipmgr {telnet|snmp|web}

Nortel Ethernet Routing Switch 2500 Series
Security — Configuration and Management
(NN47215-505)

no lacp aggregation [port <portlist>] enable

Nortel Ethernet Routing Switch 2500 Series
Configuration — VLANs, Spanning Tree, and
MultiLink Trunking (NN47215-501)

no lldp [port <portlist>] config-notification

"no lldp config-notification command" (page 220)

no lldp [port <portlist>] status

"no lldp status command" (page 223)

no lldp tx-tlv [port <portlist>] [local-mgmt-addr]
[port-desc] [sys-cap] [sys-desc] [sys-name]

"no lldp tx-tlv command" (page 221)

no logging

Nortel Ethernet Routing Switch 2500 Series
Performance Management — System Monitoring
(NN47215-502)

no logging remote address

Nortel Ethernet Routing Switch 2500 Series
Performance Management — System Monitoring
(NN47215-502)

no logging remote enable

Nortel Ethernet Routing Switch 2500 Series
Performance Management — System Monitoring
(NN47215-502)

Nortel Ethernet Routing Switch 2500 Series

Overview — System Configuration

NN47215-500 (323162-B)

02.02

Standard

4.1

19 November 2007

Summary of Contents for 2500 Seriess






































































































































































































































































































































































































Search results

Summary of Contents for 2500 Seriess

Reviews:

Related manuals for 2500 Seriess

Brands by name

Popular brands

Nortel 2500 Seriess, System Configuration Manual

Search results

Summary of Contents for 2500 Seriess

Reviews:

Related manuals for 2500 Seriess

Brands by name

Popular brands