Nortel 2500 Seriess System Configuration Manual Download Page 345

Page: 345 / 392

Appendix B

Default settings

345

Field

Default setting

VLAN Name

VLAN # (VLAN number)

Management VLAN

Yes, VLAN #1

VLAN State

Inactive

Port Membership

Default (all ports assigned as untagged members of
VLAN 1)

Unit

Port

Filter Untagged Frames

Port Name

Unit 1, Port 1

PVID

Tagging

Untagged Access

Unit

Port

PVID

1 (read only)

Port Name

Unit 1, Port 1 (read only)

Unit

Status

Enabled (for all ports)

LnkTrap

Autonegotiation

Enabled (for all ports)

Speed/Duplex

100Mbs/Half (when Autonegotiation is Disabled)

Autonegotiation

Enabled

Speed/Duplex

100Mbs/Half (when Autonegotiation is Disabled)

Flow Control

Disabled

Trunk

1 to 6 (depending on configuration status)

Trunk Members (Unit/Port)

Blank field

STP Learning

Normal

Trunk Mode

Basic

Trunk Status

Disabled

Trunk Name

Trunk #1 to Trunk #6

Traffic Type

Rx and Tx

Monitoring Mode

Disabled

Monitor/Unit Port

Zero-length string

Unit/Port X

Zero-length string

Limit

0 pps

Nortel Ethernet Routing Switch 2500 Series

Overview — System Configuration

NN47215-500 (323162-B)

02.02

Standard

4.1

19 November 2007

Summary of Contents for 2500 Seriess






































































































































































































































































































































































































Search results

Summary of Contents for 2500 Seriess

Reviews:

Related manuals for 2500 Seriess

Brands by name

Popular brands

Nortel 2500 Seriess, System Configuration Manual

Search results

Summary of Contents for 2500 Seriess

Reviews:

Related manuals for 2500 Seriess

Brands by name

Popular brands