manualshive.com logo in svg

Ness IDTECK iCON100, User Manual

Share
Download
Ness IDTECK iCON100 User Manual Download Page 9

 

 

 

101-000                                                 -9-                                               Users Manual

 

IDTeck – iCON 1 DOOR ACCESS CONTROLLER 

 
 

3.2 BOARD LAYOUT 
 

 

        

     

     

 

          Figure: NESS - iCON100 Control Board Layout   

 

 
 

DIP S/W (BOARD ID S/W, Initialize S/W)   

This BOARD ID S/W (Pin 1 ~ 5) is for the communication ID setting of the NESS - iCON100 
control board. 
This Initialize S/W (Pin 8) is to initialize and erase all user data from the memory. 

+12V and GND (Main Power) 

This is the main power connection of the control board. The NESS - iCON100 works at DC12V, 
max. 350mA current. (Excluding lock current) 

TTL #1 ~ TTL #2 

These are 2 TTL output ports at DC5V TTL level, max. 20mA current. 
The normal logical state of TTL output is Low (DC 0V) and activates to High (DC 5V). 

Relay #1 ~ Relay #2 

These are 2 FORM-C (COM, NO, NC) relay outputs at DC12V, max. 2A current. 

Summary of Contents for IDTECK iCON100





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands