Ness IDTECK iCON100 User Manual Download Page 52

Page: 52 / 60

101-000 -52- Users Manual

IDTeck – iCON 1 DOOR ACCESS CONTROLLER

APPENDIX

A. THE RELATION BETWEEN INPUT AND OUTPUT (DEFAULT)

1. The relation between input and output

* Index No. [1] ~[14]: The value indicates the operation time (seconds) of each output for the input

signal.

* Index No. [15]: The value indicates time schedule code (index) that each output operation is to

be applied.

* Index No. [16]: The value indicates the time schedule code (index) that each input: #1(Exit button)
~#5

operation is to be applied.

Index No

Relay#1 Relay#2 Relay#3 Relay#4

TTL#1

[1] Input #1(EXIT BUTTON)

[2] Input #2(Door Contact SW)

[3] Input #3

[4] Input #4

[5] Input #5

[6] Reader#1 ID OK

[7] Reader#1 ID Error

[8] Reader#1 ID T/S Error

[9] Reader#1 APB Error

[10] Reader#2 ID OK

[11] Reader#2 ID Error

[12] Reader#2 ID T/S Error

[13] Reader#2 APB Error

[14] DURESS MODE

[15] OUTPUT TIME SCHEDULE

[16] INPUT TIME SCHEDULE

Input #1 Input #2 Input #3 Input #4 Input #5

Summary of Contents for IDTECK iCON100





























































Search results

Summary of Contents for IDTECK iCON100

Reviews:

Brands by name

Popular brands

Ness IDTECK iCON100, User Manual

Search results

Summary of Contents for IDTECK iCON100

Reviews:

Brands by name

Popular brands