manualshive.com logo in svg

Ness IDTECK iCON100, User Manual

Share
Download
Ness IDTECK iCON100 User Manual Download Page 21

 

 

 

101-000                                                 -21-                                               Users Manual

 

IDTeck – iCON 1 DOOR ACCESS CONTROLLER 

 

5.5.4 READER CONNECTIONS 

Proximity Reader Connection 

- Connect (+) wire of the Proximity Reader to +12V of Reader port 

- Connect (-) wire of the Proximity Reader to GND of Reader port 
- Connect Data-0 wire of the Proximity Reader to D0 of Reader Port 
- Connect Data-1 wire of the Proximity Reader to D1 of Reader Port 

 

 

Compatible Readers

: 

NESS - iCON100:

 Standard 26bit Wiegand Format Proximity Readers 

 

Standard 26bit W 8bit Burst Format Proximity and Keypad Readers. 

NESS - iCON100SR:

 Standard 34bit Wiegand Format Proximity Readers 

 

Standard 34bit W 8bit Burst Format Proximity and Keypad Readers. 

 

Recommended Readers

: 

For NESS - iCON100:

   RF-TINY, RF10, RF20, RF30, RF70, RF500, RFL200, 

RFK101 

 

 

 

 

FGR006, FGR006EX, iP10, iP20, iP30, iPK101 

For NESS - iCON100SR:

   SR10, SR20, SR30, SRK101, FGR006SR, FGR006SRB 

 

                 

Figure: READER CONNECTION 

 

Summary of Contents for IDTECK iCON100





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands